--- title: CamBar Rigging Guide slug: scenario/cambar-rigging-guide docTags: createdAt: 2025-06-17T09:01:03.386Z --- # Introduction Rigging the CamBar appropriately to your camera is vital for good quality tracking. This section provides some recommended configurations based on your camera and expected use case. Specific 3rd party hardware components are listed, however they are often interchangeable with similar parts from other sources # Marker Mode – Cine Style  Here we describe a recommended configuration for mounting the CinCraft Scenario CamBar to a cinema style production camera where 15 or 19mm rods are available, and either ceiling or floor tracking is expected. ### Pre-Requisites Production Camera must feature 15mm or 19mm rods ### Recommended Components  - **A** - CAMVATE Standard 15mm Dual-port Rod Clamp Railblock With One-sided ARRI Rosette Connecting M6 Mount For Shoulder Mount Rig - [Retailer Link](https://www.camvate.com/products/camvate-standard-15mm-dual-port-rod-clamp-railblock-with-one-sided-arri-rosette-connecting-m6-mount-for-shoulder-mount-rig-2766) - **B** - CAMVATE Standard ARRI Rosette Extension Part With M6 Lock Knob & Double 1/4" Mounting Groove - [Retailer Link](https://www.camvate.com/products/camvate-standard-arri-rosette-extension-part-with-m6-lock-knob-double-1-4-mounting-groove-2546) OR for 19mm rods - **C** - CAMVATE 15mm & 19mm Dual-port Rod Clamp With Double Ended M6 ARRI Style Rosette Mount - [Retailer Link](https://www.camvate.com/products/camvate-15mm-19mm-dual-port-rod-clamp-with-double-ended-m6-arri-style-rosette-mount-2310) - Screw Set for Camera Accessories  - [Retailer Link](https://www.smallrig.com/uk/smallrig-screw-set-for-camera-accessories-aak2326.html) ### Mounting Guidelines  ::::WorkflowBlock :::WorkflowBlockItem Using 2 x 1/4" screws, affix part **B** to the rear of the CamBar ![](https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-UlPXhMYbaAC-pjF3wXDF8-20250617-161340.png) ::: :::WorkflowBlockItem Place part A onto the camera rods and tighten For **ceiling** tracking use the upper rods For **floor** tracking use the lower rods ::: :::WorkflowBlockItem Attach the CamBar to the rods using the rossette. Align the CamBar either vertically up or down depending on whether ceiling or floor tracking **Ceiling** ![](https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-aWE8H7lQdKK-TbjmWk05O-20250617-203141.png) **Floor** ![](https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-TimczudN8BE8-ZV2gLNZy-20250617-204035.png) ::: :::: *** # Marker Mode - Broadcast Style This configuation is designed for ceiling marker tracking when using broadcast style cameras. It uses a clamp and long extension plate to affix to the camera grip and project the CamBar out atop the lens. This configuration is ideal when working with jibs/cranes as it prevents the head of the crane obstructing the CamBar's view of the markers ### Pre-Requisites Camera requires a top handle with at least 1 x 1/4" mounting hole on it ::Image[]{src="https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-lWc_hJ8j9YePvKqnA5Ltd-20250617-110133.png" size="64" width="1019" height="898" position="center" showCaption="false"} ### Recommended Components - **A** - Haoge HQR-400 400mm Multi-purpose Long Quick Release Plate Extender Sliding Rail for Camera Tripod Ballhead Ball Head Clamp fit Arca Swiss - [Retailer Link](https://www.amazon.co.uk/dp/B07RFLQTTG/ref=cm_sw_r_apan_i_ENSJKYX95942DES0JXT3?th=1) - **B** - SUNWAYFOTO SM-76 Saddle Mount Rifle Gun Adapter for Tripod Arca Swiss QR Plate - [Retailer Link](https://www.amazon.co.uk/dp/B09F3SRFF3/ref=cm_sw_r_apan_i_PR7V0EE5H9KNCF4KKZCC) - **C** - 1/4" UNC Through Hole 20mm Camera Switch Adapter 1/4 Female To 1/4 Female Screw - [Retailer Link](https://www.amazon.co.uk/Through-Adapter-Suitable-Accessories-Electric/dp/B0D25VDFG9?source=ps-sl-shoppingads-lpcontext\&ref_=fplfs\&psc=1\&smid=AONBLG9HE2JL7) - **D** - Andoer Quick Release Clamp and Quick Release Plate for Arca Swiss Standard Tripod Ball Head - [Retailer Link](https://www.amazon.co.uk/Andoer-Aluminum-Adjustable-Knob-Type-Compatible/dp/B078H83PXC/ref=sr_1_11?keywords=arca%2Bswiss%2Bbase%2Bplate\&qid=1657062445\&sprefix=arca%2Bswiss%2Bbase%2Caps%2C44\&sr=8-11\&th=1) - **E** - 1/4" Male to 1/4" Male Threaded Tripod Screw Adapter - [Retailer Link](https://www.amazon.co.uk/dp/B093BJVTZ7/ref=sspa_dk_detail_5?psc=1\&pd_rd_i=B093BJVTZ7\&pd_rd_w=ffSuw\&content-id=amzn1.sym.9a64fe05-cdee-4d53-a27b-f3614d726545\&pf_rd_p=9a64fe05-cdee-4d53-a27b-f3614d726545\&pf_rd_r=QPJ4YDVY47WBP8GW5NWV\&pd_rd_wg=I6YY6\&pd_rd_r=75f7c82e-e297-475d-8320-854a8e2b0657\&s=photo\&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWxfdGhlbWF0aWM) - **F** - CAMVATE Swivel and Tilt Adjustable Monitor Mount with 1/4"-20 Anti-Twist Mount - [Retailer Link](https://www.camvate.com/products/camvate-swivel-and-tilt-adjustable-monitor-mount-with-1-4-20-anti-twist-mount-3848) - Screw Set for Camera Accessories  - [Retailer Link](https://www.smallrig.com/uk/smallrig-screw-set-for-camera-accessories-aak2326.html) ### Mounting Guidelines ::::WorkflowBlock :::WorkflowBlockItem Connect the Arca quick release base (D) towards the rear of the extender plate (A) using a 1/4" camera screw ::: :::WorkflowBlockItem Connect the saddle clamp (B) to the Arca base using the Arca base integrated in the clamp ::: :::WorkflowBlockItem Connect the Monitor Mount (F) to the opposite side and end of the extender plate (A) ::: :::WorkflowBlockItem Position the extender plate (A) over the camera grip and fix in place using the saddle clamp ::: :::WorkflowBlockItem Use a 1/4" camera screw to connect the extender plate (A) to the rigging point at the front of the camera grip. The riser part (C) can be added to the rigging point if required using the 1/4" Male to 1/4" Male Adapter (E) ::: :::WorkflowBlockItem Connect the CamBar to the monitor mount (F) using the integrated screw ::: :::WorkflowBlockItem ![](https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-dRe1YOLj8SsYF7jutuSgv-20250626-144241.png) ::: :::: *** # Natural Mode - Cine Style Natural tracking mode typically requires more flexibility in the orientation of the CamBar to ensure good tracking quality. This configuartion uses either a 15mm or 19mm rod clamp and monitor mount to allow significant flexibility in orientation ### Pre-requisites Production Camera must feature 15mm or 19mm rods ### Recommended Components - **A** - CAMVATE Swivel and Tilt Adjustable Monitor Mount with 1/4"-20 Anti-Twist Mount - [Retailer Link](https://www.camvate.com/products/camvate-swivel-and-tilt-adjustable-monitor-mount-with-1-4-20-anti-twist-mount-3848) - **B** - CAMVATE Standard 15mm Dual-port Rod Clamp Railblock With One-sided ARRI Rosette Connecting M6 Mount For Shoulder Mount Rig - [Retailer Link](https://www.camvate.com/products/camvate-standard-15mm-dual-port-rod-clamp-railblock-with-one-sided-arri-rosette-connecting-m6-mount-for-shoulder-mount-rig-2766) Or for 19mm rods - **C** - CAMVATE 15mm & 19mm Dual-port Rod Clamp With Double Ended M6 ARRI Style Rosette Mount - [Retailer Link](https://www.camvate.com/products/camvate-15mm-19mm-dual-port-rod-clamp-with-double-ended-m6-arri-style-rosette-mount-2310) ### Mounting Guidelines ::::WorkflowBlock :::WorkflowBlockItem Attach the adjustable monitor mount (A) to the rod clamp (B or C) using the integrated 1/4" camera screw ::: :::WorkflowBlockItem Mount the rod clamp (B or C depending on rod type) to the camera rods. Either the upper or lower rods can be used depending on the tracking requirements ::: :::WorkflowBlockItem Fix the CamBar to the monitor mount (A) using the integrated 1/4" camera screw ::: :::WorkflowBlockItem Orientate the monitor mount in the preferred tracking direction and ensure that the mount is securely locked to prevent pan or tilt movement of the mount ::: :::WorkflowBlockItem ![](https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-2ew-l0RHvV9ja04_a824I-20250630-213708.png) ::: :::: *** # Natural Mode - Broadcast Style With 15/19mm rods likely to be unavailable the accessory mount on the camera grip can be used in conjunction with an adjustible monitor mount to provide a flexible mounting configuration ### Pre-requisites Camera requires at least 1 x 1/4" mounting hole ### Recommended Components - **A** - CAMVATE Swivel and Tilt Adjustable Monitor Mount with 1/4"-20 Anti-Twist Mount - [Retailer Link](https://www.camvate.com/products/camvate-swivel-and-tilt-adjustable-monitor-mount-with-1-4-20-anti-twist-mount-3848) ### Mounting Guidelines ::::WorkflowBlock :::WorkflowBlockItem Connect the Monitor mount (A) to the accessory mount at the front of the camera grip ::: :::WorkflowBlockItem Connect the CamBar to the monitor mount (A) ::: :::WorkflowBlockItem Orientate the CamBar in the preferred direction for tracking quality and ensure that the monitor mount is securely fastened to prevent unnecessary pan or tilt movement ::: :::WorkflowBlockItem ::Image[]{src="https://api.archbee.com/api/optimize/qD4GJYL5qMffFW6GWjgo7-0y7CU0sSVFPCCXyTzS0ol-20250618-135814.png" size="62" width="1024" height="1024" position="center" showCaption="false"} ::: ::::